Skip to content
AHYW official logo

安徽省亚威机床制造有限公司
Bowang, Maanshan, Anhui

AHYW laser cutting: plan the sheet before the power

Compare a 1500 × 3000 mm sheet bed with the 14000 × 3200 mm high-power reference. Define loading, gas, cut quality and the actual source/head package.

Company, two laser pages, original images and government product list reviewed 8 October 2026

Choose a sheet route your shop can actually handle

Standard sheets and mixed nests

For 1500 × 3000 mm stock, start with YWFL-3015. Include the largest blank, clamps or support margins, kerf spacing, pierce locations and the smallest finished features in a representative nest. Working area is not a promise that every full-bed outline can be cut without edge or fixture restrictions.

Long or wide blanks

YWFL-14032-12000W has a published 14000 × 3200 mm working area. Before choosing it, show the route from delivery vehicle to sheet storage, loading, cutting and unloading. State sheet mass, lifting points, flatness and how operators remove large parts and scrap without standing in the active cutting area.

A large sheet bed is useful only when it fits the actual job flow. Ask for the quoted machine's foundation and complete operating layout, including service access, fume collection, coolant equipment, stock staging and lifting clearance. The model number and working area do not establish its installation footprint.

Keep bed size separate from the laser package

Published model-table entries, with power and configuration conflicts left for a dated proposal.
ReferenceYWFL-3015YWFL-14032-12000W
X/Y working area1500 × 3000 mm14000 × 3200 mm
Z travel100 mm100 mm
Laser outputConfirm the ordered source and power; photograph below is marked 1500WModel table lists ≥12000W; confirm matching source and head
Control/software familyBochu fiber-laser cutting systemBochu fiber-laser cutting system
Table-listed file formatsDXF / PLT / AIDXF / PLT / AI
Material referenceStainless, carbon and galvanized sheet; thickness requires trialStainless, carbon and galvanized sheet; thickness requires trial
Existing model recordYWFL-3015 ↗YWFL-14032-12000W ↗

Swipe to compare the two bed references.

Official workshop photograph marked YWFL-3015-1500W
The original workshop image is marked YWFL-3015-1500W. It shows this pictured configuration, not every power option or an included loading system.

The 3015 page's power row does not agree with its wider series description or this pictured 1500W configuration. The high-power page's model table identifies a 12 kW reference, while surrounding descriptions include lower-power lens and series limits. Request one dated bill of materials and specification for the source, cutting head, optics, cooling and bed that will actually ship.

Both are presented as open-type sheet-cutting references. General paragraphs about shuttle tables or tube chucks do not establish that either quoted machine includes those assemblies. Tube cutting needs its own chuck range, supports, residual length and model-specific evidence.

Prove the edge you will use in production

Laser output alone does not determine acceptable cutting thickness, speed or finish. Send the actual grade, thickness, coating, surface condition and blank flatness. Agree the assist gas, pressure, nozzle, focal setup, pierce method and acceptance criteria for each material/thickness combination.

  1. Use a representative nest

    Include long straight edges, corners, narrow webs, holes and the smallest intended features. Test both central and edge-of-sheet locations where the job requires them. Preserve the nest, parameters and material identification with the results.

  2. Inspect the delivered edges

    Measure contour dimensions and hole form, and inspect burr, dross, edge roughness and heat effects against the agreed requirement. If parts will be bent, welded or coated, include those downstream requirements rather than accepting only an attractive sample photograph.

  3. Time loading through unloading

    Record piercing, cutting, repositioning if any, scrap handling and unloading. The pages' motion-speed and maximum-cutting-speed entries are not a demonstrated rate for your material and thickness. Ask for the full tested cycle and gas use.

  4. Repeat after warm-up

    Run the planned batch conditions, including cooling and consumable changes. Axis location figures describe machine motion; finished-contour acceptance needs its own measuring procedure, temperature and sampling.

Specify the support systems with the machine

Gas and extraction
Define the gas source, regulator, pressure/flow at the head, filtration and consumption basis. Obtain the fume-collection design and facility requirements for the material, thickness and actual open-bed arrangement. Do not assume the bed photograph establishes the safety measures required at your destination.
Electrical and thermal demand
Request supply voltage/frequency, installed electrical load, chiller performance and ambient conditions for the exact source and head. The tables' 3.8 kW chiller entry is not the machine's total power demand or verified heat-removal capacity.
Software and handover
The pages describe English-language Bochu software, drawing-file import, nesting and height control. Specify the actual software/controller version, licenses, file conventions, kerf compensation and training. Demonstrate height calibration, pierce recovery and restart on the trial job.
Service and consumables
The manufacturer describes installation/use training and engineers available for overseas service. Agree the destination coverage, travel costs, commissioning responsibility and response arrangements. List spare nozzles, protective optics, lenses, filters and the maintenance schedule for the delivered head.

AHYW's sheet-metal equipment scope

The official English site identifies Anhui Yawei Machine Tool Manufacturing Co., Ltd., established in 2005, in Bowang, Maanshan. The corresponding machine image names 安徽省亚威机床制造有限公司. Its catalogue covers press brakes, shears, fiber lasers, plate rolling, grooving and other sheet-metal machinery. This company is kept distinct from similarly named manufacturers in other provinces.

The final 2024 Anhui Industrial Boutique product list, hosted by the Lu'an government, names the same Chinese company at entry 74 for YWTP high-precision tandem bending equipment. That is a specific historical bending-product record, not certification of the two laser references.

This page uses reviewed manufacturer material for catalogue facts and CNCVerified analysis for sheet handling and purchase acceptance. Other catalogue families require their own model evidence. Any certificate required for an order must be current and identify the holder, machine scope and applicable documentation.

Send the material list and one real nest

Include sheet grade, thickness range, blank dimensions/mass, drawing or nest, smallest features, edge-quality requirements, downstream operations, batch target and destination. State the desired bed, actual source/head package, gas supply, loading method and acceptance test.

Send AHYW RFQ ↗