Skip to content
Official Huaji brand logo

HUAJI · 华集数控
Xiangcheng, Suzhou, Jiangsu

Huaji CV: fit the loaded setup

CV-850 and CV-855 share 800 mm X travel. Compare fixture height, Y/Z space and load, then specify the spindle and guide configuration.

Official company and two CV model pages reviewed 8 October 2026

Put the fixture and assembled tool into the comparison

A component fitting within XYZ travel does not establish access to all its features. Include the fixture height, clamps, blank dimensions and complete tool/holder length. Check both the low and high spindle-nose positions, tool changes and access at the table's edges.

Separate official CV/DV-850 and CV-855(D,L,S) tables; final configuration requires a matching installation and setup drawing.
Setup dimensionCV-850 / DV-850 pageCV-855(D,L,S) page
X / Y / Z travel800 / 500 / 500 mm800 / 550 / 550 mm
Spindle nose to table120–620 mm120–670 mm
Spindle center to Z-axis cover plane520 mm570 mm
Table / maximum load1000 × 500 mm / 700 kg1000 × 550 mm / 850 kg
T-slots: width × count × spacing18 mm × 5 × 90 mm18 mm × 5 × 90 mm
Approximate machine dimensions2.6 × 2.3 × 2.6 m2.8 × 2.3 × 2.65 m
Approximate machine mass5.3 tonnes6 tonnes
Existing model pageCV-850 ↗CV-855 ↗

Swipe the comparison on a narrow phone.

The CV-855 table gives more Y/Z travel and a higher listed table load, but the same X travel. Check the total loaded fixture and its mass distribution. A raised vise may use spindle clearance before it uses Z travel; a long tool or rotary fixture may impose another limit. Request the permitted arrangement rather than assuming the whole table is an unrestricted machining envelope.

See the structure behind the setup

Official structural view published on the Huaji CV-850 and DV-850 page
Original CV/DV-850 page structural view. The numbered illustration does not define every delivered option.
Official structural view published on the Huaji CV-855 variant page
Original CV-855 page structural view, without the enclosure. Confirm the exact D, L or S arrangement in the proposal.

The manufacturer describes a broad base and column arrangement, spindle-head cooling and protective guide/screw covers. These are design descriptions, not evidence of accuracy under your cutting load or a complete environmental-protection specification.

Check access for changing tools, removing chips and servicing the machine in its installed position. Use the final enclosed-machine drawing for door, electrical-cabinet, coolant-system and maintenance clearances; a bare-machine image is not a transport or installation drawing.

Keep alternative configurations in separate quote lines

Spindle speed, interface and power
Both pages list 10000 rpm, with starred 8000/12000/15000 rpm alternatives. CV-850 lists BT40 and a starred HSK A63 alternative; CV-855 also lists a starred BBT40 alternative. Do not combine the fastest spindle with every power/interface option without an explicit package.
Guide arrangement and rapid movement
CV-850 lists 35/35/35 mm roller guides and 48/48/48 m/min rapid movement, with a starred 36/36/36 alternative. CV-855 lists 35/45/45 mm guides, identifies the L arrangement as hard guides, and lists 36/36/36 m/min, L:24, with a starred 48/48/48 alternative. Confirm what the selected suffix includes.
Magazine and tool assembly
Both pages list 24 tools and a starred 30-tool alternative, 300 mm maximum tool length, 8 kg maximum tool mass and diameter entries of 76/150 mm. The table does not explain the condition for each diameter; ask which adjacent positions must remain empty and how the loaded holder is measured.

CV-850 motor entries are 7.5–11 kW with a starred 11–15 kW alternative. CV-855 lists 11 kW with starred 15 and 18.5 kW alternatives. Duty and torque curves are not defined in those entries. Ask for the selected spindle's usable torque across the intended milling, drilling and tapping speeds.

The published 2.8-second tool-to-tool change is not chip-to-chip time. Account for approach, retract, spindle acceleration and other cycle steps. The table's generic “4/5-axis” motor-field wording does not establish an included rotary table, simultaneous five-axis control or its usable envelope.

Demonstrate the part under the quoted configuration

Loaded cutting and feature access

Run the proposed part with the intended material, fixture and tool assemblies. Inspect features at the difficult corners and depths, and record any reclamping. Include roughing and finishing conditions that matter to the drawing, rather than accepting a motion demonstration.

Thermal condition and process protection

Agree warm-up, coolant conditions and measurement temperature. If processing quartz, ceramics or another abrasive material, define the process, filtration, extraction, guide protection and maintenance requirements explicitly; the company's market description does not prove that either standard CV configuration includes them.

Repeatable inspection and handover

The two tables list ±0.005 mm positioning and ±0.003 mm repeat-positioning accuracy. Establish finished-part acceptance separately, including datums, instruments and measurement after fixture release where relevant. Retain the trial report, programs, offsets, tool/fixture lists and commissioning criteria.

Specify controller, electrical supply, compressed air and all auxiliaries in the installation package. The tables list 20 kVA electrical demand and 7 kgf/cm² air pressure, but do not quantify the complete air flow or every auxiliary's consumption. Obtain those site requirements before installation.

Huaji's CNC development and manufacturing business

The official company introduction identifies 苏州华集数控科技有限公司 in Yangchenghu, Xiangcheng, Suzhou. It describes CNC-machine development, production, inspection capability and supporting repair services, with vertical machining, drilling/tapping, gantry, horizontal, five-axis and turn-mill families.

The original Suzhou 2019 proposed high-tech incubation list names the exact company in Xiangcheng at entry 3098, page 74. That dated proposed listing supports the historical corporate cross-check; it is not current certification or model acceptance.

This profile compares the two existing CV entries; other families need their own model and configuration evidence. The loaded-setup, quote and acceptance guidance is CNCVerified's editorial analysis. Agree the currently contracting entity, destination service, commissioning, training and warranty in writing.

Send the loaded setup and tool list

Attach the part drawing, material, blank and fixture dimensions, total table load, tool/holder lengths and required features. Name CV-850 or the intended CV-855 suffix, spindle/interface choices, batch requirement, inspection method and destination.

Send Huaji RFQ ↗