Skip to content
Official Lunan T logo

山东鲁南精工机械有限公司
Tengzhou, Shandong

Lunan VMCs: fit the fixture, then specify the package

Compare VMC850SL and VMC1160 by loaded table space and tool-to-part clearance. Keep the controller, magazine and optional fourth axis on the quotation.

Company, two model pages, service material and association record reviewed 8 October 2026

The same Z travel can give different setup clearance

Both models list 600 mm Z travel, but the spindle-nose-to-table endpoints differ: 170–770 mm for VMC850SL and 120–720 mm for VMC1160. Draw the table, fixture, clamped part, holder and tool together. Check access to the lowest machining feature and the height needed for retracts and tool exchange.

VMC1160 provides more X/Y travel, table area and published load; its upper spindle clearance is not larger. A tall fixture that needs the 850SL's upper position deserves a separate check on 1160. Table load includes the fixture, workpiece and any rotary equipment, with the permitted distribution confirmed for the ordered machine.

Exact VMC850SL and VMC1160 columns from their respective model pages.
Setup constraintVMC850SLVMC1160
X / Y / Z travel800 / 500 / 600 mm1100 / 600 / 600 mm
Table length × width1100 × 500 mm1200 × 600 mm
Table load600 kg800 kg
Nose-to-table endpoints170–770 mm120–720 mm
Spindle center to column guide face580 mm710 mm
T-slot arrangement5 slots, 18 mm width, 100 mm pitch5 slots, 18 mm width, 100 mm pitch
Listed spindle range / motor60–8000 rpm / 7.5 kW60–8000 rpm / 11 kW
X/Y rapid / Z rapid32 / 24 m/min32 / 24 m/min
Machine net mass5700 kg6800 kg
Listed dimensions2700 × 2300 × 2500 mm3100 × 2500 × 2800 mm

Swipe to compare both fixture envelopes.

Keep the exact model suffix in view

Manufacturer's VMC850SL photograph with VMC850SL model plate
Original VMC850SL product photograph.

VMC850SL: three linear-guide axes

The SL column specifies three linear-guide axes. Nearby SLD, SL2 and L columns share the same travel, but differ in spindle speed, guide arrangement and rapids. The SLD's 12,000 rpm figure and SL2's mixed linear/box-guide arrangement do not describe this SL entry.

Its configuration list specifies a FANUC 0i MF5 control, with other controls selectable. Request the exact control version, installed options and postprocessor rather than assuming all catalogue variants ship with the same functions.

Open VMC850SL ↗
Manufacturer's VMC1160 photograph with VMC1160 model plate
Original VMC1160 product photograph.

VMC1160: wider fixture and heavier loaded table

The 1160 column increases Y travel to 600 mm and table load to 800 kg. Its configuration list describes 45-size roller guides on X/Y/Z, an 11 kW spindle motor, BT40 spindle and a 24-position disc magazine.

The listed control is KND2000M, with other brands optional. The adjacent VMC855 and XHC715 figures belong to different machines. Specify the chosen 1160 control and options independently of the 850SL package.

Open VMC1160 ↗

Resolve the magazine before counting the job's tools

The VMC850SL page's standard-configuration list describes a 16-tool umbrella magazine and offers a 24-tool disc magazine as an option; its technical table lists 24 positions. Have the proposal name one supplied magazine and its assembly limits. Do not turn these conflicting entries into a guaranteed standard 24-tool package.

The technical tables for both models give 80 mm tool diameter with neighboring positions occupied and 125 mm with neighboring positions empty, 300 mm length and 10 kg tool mass. Confirm these limits for the magazine actually supplied. Count reserved empty positions, assembled holder/tool mass and exchange clearance before assuming every station can be used.

Cutting and chip management
The 850SL lists through-spindle coolant and an automatic chip conveyor among options. The 1160 configuration describes external cooling and manual rear chip removal. Deep drilling or unattended batches need a specified coolant pressure/flow, filtration and chip-removal package.
Rotary fixture and measurement
A fourth axis and tool setter appear as 850SL options. Specify the rotary unit, control channels, clamping, fixture mass and cable clearance. A fourth-axis option does not establish five-axis simultaneous machining or included workpiece probing.
Programming and restart
Provide a representative CAM program and required tapping, offsets and recovery behavior. Agree licensed control functions, postprocessor delivery and a safe restart demonstration after an interrupted operation.

Use the offered process support to prove one complete job

The service material describes machine selection, process planning, tool selection, fixture design and trial-part machining. Define the deliverables for your order: a fixture drawing, cutting-tool list, trial program, measured part and the person responsible for installation and training. Its older body text uses the Lunan Machine Tool name; clarify the current contracting and service entities in the agreement.

  1. Run the production setup. Use the intended material, complete fixture and loaded tool list, including the deepest feature and any second setup. Measure loading, exchanges, cutting and chip clearing as one cycle.
  2. Agree the inspection method. Check datums, hole locations, flatness or finish as required by the drawing, including after clamp release. Axis positioning and repeatability entries are machine-motion figures, not guaranteed part tolerances.
  3. Prepare the destination. Obtain the foundation, floor loading, leveling and lifting drawings; electrical supply and installed auxiliary demand; access for doors, maintenance and chip removal. Listed machine dimensions are not the whole operating footprint.
  4. Define acceptance and support. Record permitted measurement conditions, sampling, training language, manuals, spare parts, warranty scope and destination service responsibilities. Agree response and travel arrangements rather than assuming a website service statement is an overseas SLA.

The present company behind the Lunan brand

The current official company page identifies Shandong Lunan Precision Machinery Co., Ltd. (山东鲁南精工机械有限公司) in Tengzhou. It describes formation in early 2020 and authorized use of the T and Lunan trademarks. This profile keeps that present company distinct from earlier brand history.

The Shandong Machine Tool and General Machinery Industry Association's eighth council list names the same company at council-member entry 24. This is an association record, not a machine certification or independent factory audit.

The catalogue covers five-axis machining, flexible turning/milling cells, turning centers, horizontal and gantry machining, conventional VMCs and special equipment. The two existing VMC records are the reviewed comparison here; other families need their own model-level evidence. Manufacturer figures are separated from CNCVerified's fixture and acceptance analysis. Current certificates, if required for the purchase, must identify the holder, scope, model and validity.

Send a fixture-height sketch with the drawing

Include the part and blank, material, fixture footprint and total mass, stack height, tool lengths/diameters/masses, station count, coolant and rotary requirements, controller/CAM needs, batch target and destination. Name VMC850SL or VMC1160 and the magazine to quote.

Send Lunan RFQ ↗