Skip to content
SHENYANG
DIYI

沈阳第一机床制造有限公司
Shenfu, Shenyang, Liaoning

Diyi VMC: check your existing tools

Compare VMC650e, VMC850e and VMC640 for fixture space, magazine capacity and assembled-tool limits before replacing a machine.

Company, milling catalogue and three model pages reviewed 8 October 2026

BT40 alone does not make the tool chain compatible

Start with the assembled holders, pull studs and tools you plan to reuse. The two e-model pages list MAS403:BT40 holders and MAS403:LDA-BT40 pull studs. Match the ordered spindle and drawbar specification, then check magazine clearances and loaded tool mass.

Published tool limits from three separate official model pages.
Tool-chain constraintVMC650eVMC850eVMC640
Magazine arrangement16-position umbrella24-position disc16 positions; umbrella/disc listed
Maximum tool length200 mm250 mm200 mm
Maximum tool mass7 kg7 kg5 kg
Diameter with all positions occupied80 mm80 mmNot specified on this page
Diameter with adjacent positions empty125 mm125 mmNot specified on this page

Swipe the comparison on a narrow phone.

A large face mill may consume more than one usable position. Mark required empty neighbors in the tool list and count the remaining tools for the whole job. Ask how length and mass are measured for the complete assembly, and verify exchange clearance near clamps and tall fixtures.

The e-model pages describe rigid tapping with spindle-position feedback, but do not give a spindle-speed figure in their tables. The VMC640 separately lists a synchronous-belt spindle, 100–8000 rpm and 5.5 kW. Do not apply that speed range to either e model. The e-model power entries are 5.5/7.5 kW and 7.5/11 kW respectively; ask for the selected motor's duty and torque curve.

Then place the loaded fixture inside the working space

Table dimensions, travel and spindle clearance describe different constraints.
Fixture dimensionVMC650eVMC850eVMC640
X / Y / Z travel600 / 400 / 500 mm800 / 500 / 500 mm600 / 400 / 510 mm
Table length × width900 × 400 mm1000 × 500 mm700 × 410 mm
Allowed table load500 kg600 kg400 kg
Spindle nose to table, published endpoints130–630 mm150–690 mm150–660 mm
T-slots3 × 18 mm5 × 18 mm5 × 14 mm, 63 mm pitch
X / Y / Z rapid24 / 24 / 20 m/min24 / 24 / 18 m/min24 / 24 / 20 m/min
Existing modelVMC650e ↗VMC850e ↗VMC640 ↗

Swipe the table to compare all three models.

650e and 640 share 600 × 400 mm X/Y travel, but their tables, loads and tool limits differ. Compare the actual bolt pattern, fixture footprint and total mass. The larger 850e increases X/Y space and table load; it does not automatically preserve every existing setup or improve cycle time.

Use the final spindle/fixture drawing for the quoted machine. In particular, the 850e page's spindle-clearance endpoints span 540 mm while its listed Z travel is 500 mm; those entries should not be combined into an invented usable envelope. Confirm the lower position with the intended tool and the upper position needed for retracts and tool changes.

Keep the model and suffix on the proposal

Manufacturer's VMC650e product image
Original image on the VMC650e page.

VMC650e: 16-tool job planning

The official description uses a fixed column, cross-moving X/Y table and mechanically counterbalanced spindle head. Work through every required tool and any empty neighbor positions before assuming a 16-position magazine completes the operation in one run.

Manufacturer's VMC850e product image
Original image on the VMC850e page.

VMC850e: more stations and longer tools

Its 24-position disc magazine and 250 mm listed tool-length limit differ from 650e. Check the full tool assembly against the fixture and exchange motion. The current catalogue also has an entry called VMC850 without e; request the exact suffix and matching specification.

Manufacturer's product image on the VMC640 page
Original image assigned to VMC640 by its official page.

VMC640: compact table, different tool limits

The page describes three linear guides, servo axis drives with semi-closed-loop control and a belt-driven spindle. Its 5 kg tool limit is below the e models' 7 kg entry. Confirm the offered umbrella or disc magazine, pull-stud specification and loaded-tool exchange conditions.

Agree the cutting test and destination service together

Test the whole operation
Run the intended material, fixture and tool assemblies, including tapping, difficult depths and any second setup. The e models list 7 seconds tool-to-tool; VMC640 lists 2.5 seconds without the same measurement definition. Measure complete chip-to-chip and job cycles before comparing those entries.
Inspect the finished part
For VMC640, ±0.008 mm positioning and ±0.005 mm repeat positioning are axis figures. Set part tolerances, datums, thermal conditions, sampling and inspection after clamp release separately. Do not turn catalogue precision or a motion demonstration into accepted production capability.
Prepare the site and handover
The e tables list 20 kVA and 0.5–0.7 MPa air; VMC640 lists 15 kVA. Obtain supply voltage/frequency, compressed-air pressure and flow, coolant and auxiliary demands for the ordered configuration. The VMC640 air-pressure entry is not usable for site design.

The company publishes installation-acceptance-based warranty service for the period stated in the contract, with exclusions for human damage and force majeure, and describes operation, safety and maintenance training. Put destination coverage, travel/parts costs, response arrangements, controller/software version, training language and spare-part availability in the actual agreement; no fixed warranty duration or overseas response time is established by that policy.

The company and catalogue behind these three entries

The official company page identifies 沈阳第一机床制造有限公司 in the Shenfu area of Shenyang, Liaoning, supplying machine-tool manufacturing, sales and technical service. Its catalogue covers turning, drilling, milling and boring/milling, including conventional and CNC lathes, vertical machining, horizontal and gantry equipment.

The three model pages support this comparison. They do not establish every catalogue family's present configuration. The company name is kept exact: this profile does not transfer another similarly named Shenyang manufacturer's history, patents, listed-company status or certification.

Machine features and figures are attributed to the manufacturer's reviewed pages; tool compatibility, fixture and acceptance guidance is CNCVerified's editorial analysis. Confirm the current legal supplier and ordered specification in the contract.

Send the tools you want to reuse

Include the part drawing, material, fixture dimensions and total loaded mass. Attach the holders/pull studs, tool lengths, diameters and masses, required magazine positions, tapping details, batch target, acceptance method and installation destination. Name the exact VMC suffix.

Send Diyi RFQ ↗