
广东一机数控机床有限公司
Guangzhou, Guangdong
Guangdong Yiji: VMC or gantry?
Start with the loaded fixture, then compare the tool-change package. VMC850 and GMC2016 differ in supported mass, spindle interface and the equipment needed around the machine.
Official company account and both model pages reviewed 8 October 2026
Compare the whole setup before choosing a machine
A small part with tall fixtures can run out of tool clearance; a large part can fit the table yet exceed its load or usable travel. Include the workpiece, fixtures and carried accessories together.
VMC850 · compact vertical machining

- Travel XYZ
- 800 / 500 / 500 mm
- Table / load
- 1000 × 500 mm / 700 kg
- Nose to table
- 150–650 mm
- Spindle
- 8000 rpm / 7.5 kW
- Control
- Syntec 22MA listed
The reviewed table specifies roller linear guides on X/Y and a lined box guide on Z. Its spindle interface is written as BT40-150; confirm the exact holder, pull stud and tool-change arrangement with the offered configuration.
Read VMC850 specifications ↗GMC2016 · heavier BT50 gantry

- Travel XYZ
- 2000 / 1600 / 800 mm
- Table / load
- 2000 × 1300 mm / 5000 kg
- Bridge opening
- 1660 mm
- Nose to table
- 200–1000 mm
- Spindle
- BT50 belt / 6000 rpm
The motor is listed as 15 / 18.5 kW without a stated duty distinction. Request the power/torque curve and duty conditions for the cut. The catalog image represents the gantry family; the offered enclosure and magazine require confirmation.
Read GMC2016 specifications ↗Read only the GMC2016 column values
The official table groups GMC2016, GMC3016 and GMC4016. For GMC2016, use the first values: 2000 mm X travel, 2000 mm table length, 5-tonne load and about 20-tonne machine mass. The 3000/4000 mm lengths and 6/7-tonne loads belong to the larger models.
The magazine changes the usable tool set
GMC2016 lists automatic tool changing as optional: disc or chain arrangements with 24 or 40 positions. Ask which package is included and obtain its layout with the actual tools loaded.
Its tool table gives 112 mm diameter with neighboring tools present and 200 mm with neighboring positions empty, plus 300 mm maximum tool length and 18 kg weight. A large cutter may consume adjacent positions; nominal magazine capacity is not the number of tools your job can necessarily carry.
For VMC850, the reviewed parameter sheet does not establish magazine capacity. Specify required tool count, holder type, maximum tool size and automatic changes in the RFQ, then check the quoted equipment list.
Plan utilities and handling at the same time
VMC850 electrical package
The sheet lists three-phase 380, 220 or 415 V alternatives and an 18 kW consumption figure, separate from the 7.5 kW spindle motor. State your supply voltage/frequency and ask for the supplied electrical specification and connection requirements; these alternatives do not establish universal voltage compatibility.
Gantry foundation and unloading
GMC2016's approximate 20-tonne machine mass is distinct from its 5-tonne table load. Request the machine footprint, foundation and anchor drawing, transport sections, lifting arrangement and service clearance before committing to a building or unloading method.
Access, air and chip removal
VMC850 dimensions are listed as 2800 × 2350 × 2650 mm. Add guard/door movement, maintenance space and access for loading. Have the supplier specify compressed-air units, flow and quality, plus coolant/chip equipment for the actual material and tools.
Turn the factory inspection into an order handoff
Yiji's company account describes more than 48 hours of continuous running after assembly, followed by inspections including laser-interferometer and circular-motion checks. It also describes retaining component specifications and production records for each machine.
Before dispatch
Ask for the serial-number-specific configuration list, running record and inspection report. Agree measurement methods, warm-up, compensation settings and acceptance limits before the test. Retain the electrical drawing, controller backup, component list and maintenance documentation.
On your representative part
Provide material, stock condition, fixture, tool list and critical drawing features. Agree the cutting sequence and measure size, form, surface finish and datum relationships after unclamping. A catalog axis-positioning figure is not a finished-part guarantee.
For GMC2016, the published positioning table contains a malformed Z-axis number. Request a corrected, configuration-specific report instead of interpreting the typo as a contractual tolerance. Compare cycle time only with agreed loading, tool changes and inspection included.
The company behind the two model packages
Guangdong Yiji CNC Machine Tool describes manufacturing, sales and service activities in Guangzhou. Its official account covers vertical, horizontal and gantry machining centers, four/five-axis equipment, drilling/tapping centers, CNC lathes and machine bases. This comparison covers VMC850 and GMC2016; other categories require their own exact-model review.
A Guangzhou Commerce Bureau notice published 7 January 2022 lists the exact Chinese company name in its December 2021 foreign-trade registration table. This is a historical entity record, not a machine certification or evidence of today's export/service arrangements.
For a purchase, identify the contracting company, assembly site and destination service responsibilities in the quotation. Company statements and model tables are manufacturer-published material; the setup and acceptance guidance here is CNCVerified's purchasing analysis.
Request a configured machine and test plan
Attach the part/fixture drawing, total supported mass, material, tolerances and tool schedule. State your voltage, destination and site limits. Ask Yiji to identify the model, magazine/options, inspection documents, sample acceptance and commissioning scope as separate quote lines.
Request a Yiji quote ↗