Skip to content
Official HAITE logo

HAITE · 海特
Tengzhou, Shandong

HAITE: fit the fixture and tools before choosing the machining center

Compare a BT40 vertical center with a BT50 fixed-beam gantry. Check the loaded setup, tool-changing envelope and configuration before treating travel or spindle speed as a complete machining solution.

Company and exact VMC1270/HLC3022 material reviewed 8 October 2026

Bring the whole setup into the clearance check

Part plus fixture

Draw the blank, supporting blocks, clamps or rotary unit and locating datums. Give the combined mass and load distribution, not just the finished part's weight.

Spindle plus tool

Add holder projection, cutter length and approach/retraction clearance. A tall fixture or long tool uses available space even when the part is within XYZ travel.

Tool magazine

Check each complete tool assembly against length, weight and diameter limits. Large adjacent tools may need empty neighboring pockets; verify the proposed loading plan.

The two reviewed machines have different interfaces, tool limits and working arrangements. Choose from the component and operations, then confirm the exact spindle, control, accessories and installation package.

VMC1270: plan the BT40 tool set

HAITE official catalog image labelled VMC1270
Manufacturer image labelled VMC1270. This identified catalog image is retained rather than substituting a higher-resolution photograph of another model.

Base model table

X / Y / Z travel
1200 / 700 / 700 mm
Table / load
1300 × 600 mm / 1000 kg
Spindle nose to table
120–820 mm
Spindle / magazine
BT40; 50–8000 rpm; 24 tools
Complete tool limits
8 kg; 300 mm length; Ø80 mm full / Ø150 mm adjacent-pocket entry
Machine dimensions / air
3400 × 2420 × 2600 mm / 0.6–0.8 MPa
Open VMC1270 model details ↗

Check whether the longest boring tool can reach its feature and retract safely with the proposed fixture installed. The 120–820 mm spindle-nose range is not a maximum workpiece-height guarantee; holder and cutter geometry must be included.

The detailed table specifies a belt-driven BT40 spindle and 24-tool arm-type disc magazine. Broader selection text mentions BT50 and faster spindles for other requirements. Obtain a separately identified configuration instead of assuming these change the published VMC1270 base specification.

HLC3022: check the passage between the columns

HAITE HLC3022 fixed-beam moving-table gantry machining-center image
Original HLC3022 catalog image. Right-angle heads and rotary equipment require a specified accessory package.

Gantry envelope

Table / between-column width
3000 × 1800 mm / 2200 mm
X / Y / Z travel in table
3100 / 2400 / 1000 mm
Spindle nose to table
200–1200 mm
Spindle / magazine
BT50; 80–6000 rpm; 24 tools
Complete tool limits
18 kg; 400 mm length; Ø112 mm full / Ø200 mm adjacent-pocket entry
Machine dimensions
8400 × 5400 × 5300 mm
Open HLC3022 model details ↗

Confirm the working drawing

The same page's opening description gives 3000 mm X travel, while its model table gives 3100 mm. Obtain the current signed configuration drawing before checking a feature near either limit.

Y travel of 2400 mm does not enlarge the stated 2200 mm opening between columns. Include clamps, protrusions and loading access when checking the blank's passage. With a right-angle head, check side access and tool clearance again.

The current table does not give a table-load rating. Request combined workpiece/fixture capacity and load-distribution conditions for the actual job. Its accuracy rows use a “500 ±” format without a complete test definition; do not treat them as finished-part guarantees over the full travel.

Make configuration choices explicit

Separate the base model from an accessory or controller choice.
ChoiceWhat the reviewed material saysWhat to put in the order
ControllerVMC page lists several choices; HLC table names FANUC 0i-MF (3B) Plus and prose allows choicesOne exact control/version, licensed functions, postprocessor and backup method
Rotary machiningFour-axis control function and optional rotary equipment appear in the materialSupplied rotary unit, mounting, clearances and demonstrated indexing/simultaneous scope
Coolant and chipsVMC material offers through-spindle coolant and chip-handling optionsPressure/flow, tooling compatibility, filtration and chip-conveyor package
Gantry accessoriesRight-angle head, fourth axis and guideway arrangements require selectionExact accessory, support, changing procedure, usable geometry and inspection plan

Swipe the configuration table on a narrow phone.

A control supporting four-axis functions does not mean a rotary table is included. A suggested fifth-axis accessory does not establish an accepted five-axis simultaneous package. Demonstrate the purchased arrangement with the actual program and component.

Accept a machining process and an installable machine

Representative cutting trial

Use the specified material and difficult operations: a deep bore, long tool, pocket or cross-face feature where relevant. Record fixture, tools, cutting conditions, drawing revision and inspection method. Inspect the released part against its datums and separate loading/tool changes from cutting time.

Configuration demonstration

Exercise the agreed controller functions, tool magazine with the intended large tools, coolant/chip equipment and any rotary or angle-head operation. Record supplied equipment and settings; a general sales-video demonstration is not acceptance of your configuration.

Site and service plan

The published outer dimensions do not include every operating or maintenance clearance. Approve the installed layout, loading route, foundation, electrical and air requirements, chip/coolant access and service responsibilities at the destination. Include training, control backups and a spares list.

HAITE's machining-center business

The official company page identifies 山东海特数控机床有限公司 in Tengzhou, Shandong and describes establishment in 2006. Its catalog covers vertical, horizontal, gantry, five-axis and turning/milling equipment. The company describes assembly, sheet-metal, commissioning and inspection operations; these descriptions are not a model-specific test report.

A Tengzhou government gazette published in 2025 includes the same entity in the economic development zone's enterprise supervision list. This corroborates a dated entity/location record; inclusion is not a safety inspection pass or machine certification.

The clearance and configuration guidance above is CNCVerified's editorial analysis of the reviewed material. Confirm the seller, exact machine configuration and acceptance/service obligations in the proposal.

Send the loaded setup, not just the part size

Attach the component and fixture drawing, combined mass, material, operations and longest/largest tool assemblies. Add tolerance and inspection requirements, batch mix, controller preference and any rotary, angle-head or coolant package.

Send HAITE RFQ ↗