Skip to content
Lijie manufacturer mark

Induction hardening · complete cell scope

Henan Lijie CNC Technology Co., Ltd.

Define what is included before comparing power. Lijie's DSZP-160 heating supply and DSSK1000 workpiece station have different ratings—and still need a coil, quench and part trial.

Official pages revisited 8 October 2026 · Detailed equipment record reviewed September 2026

Chinese entity
河南力捷数控技术有限公司
Published location
Xinzheng, Henan
Buying task
Heating + motion + quench

Build the quote around three linked scopes

A supply rating describes electrical heating output. A station rating describes handling and motion. The treated part depends on both, plus the coil, quench and material condition.

  1. Supply → coil DSZP-160 provides adjustable induction output. Ask for the coil/transformer arrangement, coupling and control interfaces for the target part.
  2. Station → heating path DSSK1000 holds, moves and rotates the workpiece. Check fixture, stroke, support and clearance through the heated zone.
  3. Quench → accepted part Specify quench medium, delivery and motion, then define hardness, case depth and distortion measurements after the agreed process.

Two misleading shortcuts: DSSK1000 does not establish a 1000 mm hardening stroke; the reviewed equipment record lists 500 mm. Its 5 kW station requirement also does not replace the separate 160 kW heating-output rating.

Keep each number with its component

The complete-equipment record names the supply and station separately; confirm the ordered combination.
ComponentPublished ratingsWhat the rating does not establish
DSZP-160 supply160 kW output; adaptive 5–25 kHz; 5–100% adjustmentAchieved case depth, cycle or the complete incoming electrical demand
DSSK1000 station500 mm listed hardening stroke and swing; 30 kg part load; 0–300 rpmUsable coil access, fixture clearance or a 1000 mm heated length
Station utilitiesAC 380 V; 5 kW station electrical requirementThe heating cabinet's incoming demand or cooling/quench package

Swipe the comparison sideways on a narrow screen.

Official Lijie DSZP-160 induction-heating cabinet image

DSZP-160: quote the interface

The supply record lists three-phase 380 V at 50–60 Hz, internal/remote control and Ethernet/RS485. Forced-water cooling with a plate heat exchanger is described. Obtain the actual connection and heat-rejection schedule for the coil and duty cycle.

DSZP-160 electrical specifications ↗
Official DSSK1000 workpiece station with separate heating cabinet

DSSK1000: check the loaded motion

The recorded vertical movement is 0–100 mm/s and the workpiece load limit is 30 kg. Draw the part support, chuck, coil and quench arrangement, then verify every movement and access position against the proposed station.

DSSK1000 station specifications ↗

Ask for one combined utility and safety schedule

The heating supply, station, cooling unit and quench circuit are separate loads. Request their incoming voltage, maximum demand, water flow/quality, heat rejection, drainage and ventilation requirements as one installation document. Specify the required automation handshake, interlocks and responsibility for enclosure and loading integration.

Replacing a heating source

Provide the existing coil/transformer, impedance or matching information, cooling conditions and controls. A matching power label alone does not prove compatibility.

Buying a complete cell

List part handling, rotation/scan program, coil tooling, quench delivery, cooling, protection, commissioning and operator training as included or excluded quote lines.

A hardness trial must include the starting condition

Supply alloy grade, prior heat treatment, geometry and the required hardened/untreated zones. Agree the scan path, rotation, quench and any tempering stage. On a representative treated part, define sectioning locations, hardness traverse, case-depth interpretation and dimensional inspection. Compare results with the same starting stock condition; the 160 kW rating is not a metallurgical guarantee.

Acceptance report to request

  • Part identity, material condition and process settings used for the sample.
  • Measured hardness pattern and case depth at the agreed locations.
  • Post-process runout/distortion and the drawing's critical dimensions.
  • Complete cycle including loading, heating, quench and inspection.

Induction supplies and automation from Xinzheng

The official company account identifies Henan Lijie CNC Technology in Xinzheng and describes digital induction supplies, quenching lines, through-heating/forging equipment and customized robotic or gantry handling. These are manufacturer-published offerings; a different workpiece may need a different source, coil and station.

A 2025 Henan technology-SME intake list includes 河南力捷数控技术有限公司. That dated entity record does not certify the hardening result or the quoted machine. Exact official model tables, image screening and source limitations are recorded privately.

REQUEST A COMPLETE PROCESS

Send the part and heat-treatment target

  • Drawing, alloy, starting condition, part mass and hardened-zone map.
  • Hardness/case-depth target, distortion limit and inspection method.
  • Fixture, coil access, motion/rotation, required cycle and annual volume.
  • Available electrical/cooling utilities, cell scope and installation destination.
Prepare a Lijie RFQ ↗